Utilize este identificador para referenciar este registo: https://hdl.handle.net/1822/65678

TítuloComparative analysis of the wear of titanium/titanium and titanium/zirconia interfaces in implant/abutment assemblies after thermocycling and mechanical loading
Outro(s) título(s)Análise comparativa do desgaste das interfaces titânio/titânio e titânio/zircónia dos conjuntos pilar/implante após envelhecimento
Autor(es)Almeida, Paulo J.
Silva, Cesar L.
Alves, Jorge L.
Silva, Filipe Samuel
Martins, Ramiro C.
Fernandes, João Sampaio
Palavras-chaveDental implants
Zirconia abutments
Titanium abutments
Aging
Implantes dentários
Pilares de zircónia
Pilares de titânio
Envelhecimento
Data2016
EditoraSociedade Portuguesa de Estomatologia e Medicina Dentária (SPEMD)
RevistaRevista Portuguesa de Estomatologia, Medicina Dentária e Cirurgia Maxilofacial
CitaçãoAlmeida, P. J., Silva, C. L., Alves, J. L., Silva, et. al. (2016). Comparative analysis of the wear of titanium/titanium and titanium/zirconia interfaces in implant/abutment assemblies after thermocycling and mechanical loading. Revista Portuguesa de Estomatologia, Medicina Dentária e Cirurgia Maxilofacial, 57(4), 207-214
Resumo(s)Objectives: Due to its hardness, zirconia abutments may damage the titanium of the implant's connection during its clinical use. This study aimed to assess the wear of the seating platforms of externally hexed titanium implants when connected to zirconia abutments comparing to titanium abutments, after thermocycling and mechanical loading (TCML).Methods: Six BNT (R) S4 external connection implants (Phibo (R) Dental Solutions, Barcelona, Spain) were selected and divided into two groups (n=3): TiCE, screwed to titanium abutments and ZrCE, screwed to zirconia abutments. The samples underwent thermocycling (5000 cycles; 5-55 degrees C) and mechanical loading (1.2 x 106 cycles; 88.8 N; 4 Hz). Before and after TCML, the seating platforms of the implants were analyzed by 3D profilometry in two areas to measure their topography based on the superficial analysis parameters (Sa and Sz) parameters, and were studied by scanning electron microscopy (SEM). Data were statistically analyzed by Mann-Whitney test (p <0.05).Results: No statistically significant differences were observed in the Sa and Sz values between the implants at initial state and after TCML (p = 0.573> 0.05 and p = 0.059). The abutment's material (titanium/zirconia) did not statistically significantly influence the Sa and Sz values after TCML (p = 0.886> 0.05 and p = 0.200, respectively). However, the SEM analysis reveals a mild wear in some vertices of the hex when connected to zirconia abutments.Conclusions: After simulating five years of clinical use, the externally hexed implants, analyzed by 3D profilometry, showed similar wear patterns in the corresponding seating platforms when connected to zirconia or titanium abutments. The SEM images showed zirconia particles being transferred to the implant, which requires further study. (C) 2016 Sociedade Portuguesa de Estomatologia e Medicina Dentaria.
Objetivos Devido á sua dureza, os pilares de zircónia podem provocar danos sobre o titânio da conexão do implante durante a utilização clínica. O presente trabalho pretendeu avaliar o desgaste das plataformas protéticas de implantes de titânio com conexão hexágono externo quando conectados com pilares de zircónia em comparação com pilares de titânio, após carga cíclica e termociclagem (TCML). Métodos Foram selecionados 6 implantes de conexão externa BNT® S4 Phibo® Dental Solutions (Barcelona, Espanha), que foram divididos em 2 grupos (n = 3): TiCe aparafusados a pilares de titânio e ZrCe aparafusados a pilares de zircónio. As amostras foram submetidas a TCML (5.000 ciclos; 5–55 °C) e carga cíclica (1,2 × 106 ciclos; 88,8 N; 4 Hz). Antes e após TCML, as plataformas de assentamento de conexão dos implantes foram sujeitas a análise por perfilometria 3 D em 2 localizações para a medição da sua topografia com utilização dos parâmetros de análise superficial (Sa e Sz) e examinadas por microscopia eletrónica de varrimento(MEV). Análise estatística: Mann-Whitney test (p < 0,05). Resultados Não se observaram diferenças estatisticamente significativas nos valores de Sa e de Sz entre os implantes no estado inicial e após TCML (p = 0,573 > 0,05 e p = 0,059). O material do pilar (titânio/zircónia) não exerceu influência estatisticamente significativa nos valores de Sa e Sz após TCML (teste U p = 0,886 > 0,05 e p = 0,200, respetivamente). No entanto, a análise por MEV revelou ligeiro desgaste em alguns vértices do hexágono quando conectados com pilares de zircónia. Conclusões Após uma simulação de 5 anos de utilização clínica, os implantes com hexágono externo, analisados por perfilometria 3 D, apresentaram padrões de desgaste das plataformas de assentamento equivalentes quando conectados a pilares de zircónia ou de titânio. As imagens de MEV mostram a passagem de partículas de zircónia para o implante, aspeto que merece investigação suplementar.
TipoArtigo
URIhttps://hdl.handle.net/1822/65678
DOI10.1016/j.rpemd.2016.07.002
ISSN1646-2890
e-ISSN1647-6700
Versão da editorahttps://www.sciencedirect.com/science/article/pii/S1646289016300206
Arbitragem científicayes
AcessoAcesso aberto
Aparece nas coleções:CMEMS - Artigos em revistas internacionais/Papers in international journals

Ficheiros deste registo:
Ficheiro Descrição TamanhoFormato 
1-s2.0-S1646289016300206.pdf3,01 MBAdobe PDFVer/Abrir

Este trabalho está licenciado sob uma Licença Creative Commons Creative Commons

Partilhe no FacebookPartilhe no TwitterPartilhe no DeliciousPartilhe no LinkedInPartilhe no DiggAdicionar ao Google BookmarksPartilhe no MySpacePartilhe no Orkut
Exporte no formato BibTex mendeley Exporte no formato Endnote Adicione ao seu ORCID